Bone Mikov Project
Moderators: tr4252, The Motley Crew
Forum rules
There are a few things you should know before posting in these forums. If you are a new user, please click here and read carefully. Thanks a lot!
There are a few things you should know before posting in these forums. If you are a new user, please click here and read carefully. Thanks a lot!
Bone Mikov Project
Well I certainly can't compete with some of the originality that some of our fellow manglers have been posting, but this one turned out very nice. A mikov kit with rear bolsters, exclusive grind and factory filework. I added bone scales. This was a nice warm-up for the forum kits that are coming!
-
- Posts: 65
- Joined: Sun Dec 07, 2003 12:27 am
- Location: Proudly Canadian
-
- Posts: 65
- Joined: Sun Dec 07, 2003 12:27 am
- Location: Proudly Canadian
You are too kind Mr_Edge!
So, did you start with bone slabs and then cut them out or ?
And if you did start with slabs, what did you use for cutting?
I have been told that bone dust is seriously bad for you, and when I bought some little pieces of abalone for inlays, I was told that abalone dust will send you to the hospital post-haste. I ended up cutting it wet, while wearing a dustmask, and still felt kinda crappy after.
I have a small air-cleaner in my workshop, I hang a cloth over the intake on it, after a day of work it is black with dust.
Today I am strapping a furnace filter to a 24" box fan to serve as a bigger air-cleaner/dustcollector, and hanging it from the ceiling in my little hole(shop).
Dave
So, did you start with bone slabs and then cut them out or ?
And if you did start with slabs, what did you use for cutting?
I have been told that bone dust is seriously bad for you, and when I bought some little pieces of abalone for inlays, I was told that abalone dust will send you to the hospital post-haste. I ended up cutting it wet, while wearing a dustmask, and still felt kinda crappy after.
I have a small air-cleaner in my workshop, I hang a cloth over the intake on it, after a day of work it is black with dust.
Today I am strapping a furnace filter to a 24" box fan to serve as a bigger air-cleaner/dustcollector, and hanging it from the ceiling in my little hole(shop).
Dave
If it was easy, everybody would be doing it.
Dave they came in scale sized slabs cut flat on the inner side and naturally rounded on the outer face....roughly 5x1.5x1/2" at the center. I really didn't do any cutting, just went straight to shaping it with a belt sander. I was sure to connect the belt sander to a shop vac and run the vacuum unit outdoors...while still wearing a mask. Hand sanding I wore a mask as well. You have to fill holes, cracks and the porous ends with super glue and sand out.
Not bad to work with you just have to be careful of splintering when peening. I had made these scales a couple months back for a regular model and managed to take a chunk out of the bottom while peening. I was pretty happy to see the rear bolster model come out so I could still use the scales!
Not bad to work with you just have to be careful of splintering when peening. I had made these scales a couple months back for a regular model and managed to take a chunk out of the bottom while peening. I was pretty happy to see the rear bolster model come out so I could still use the scales!
-
- Posts: 65
- Joined: Sun Dec 07, 2003 12:27 am
- Location: Proudly Canadian
I can relate to being happy to still be able to use pre-made parts. I made the N/S bolsters for the picklock below before I actually received the liners, blade and spring etc.
I used a bolster from a 9" as a template, so of course when I got the 11" parts kits, the rear bolsters I had made were too short. I did not want to throw them away, so I spliced on a piece of brass as a filler. Jumped the gun a bit, but it worked out okay.
Cheers,
Dave
I used a bolster from a 9" as a template, so of course when I got the 11" parts kits, the rear bolsters I had made were too short. I did not want to throw them away, so I spliced on a piece of brass as a filler. Jumped the gun a bit, but it worked out okay.
Cheers,
Dave
If it was easy, everybody would be doing it.