2 Swedish Air Force survival knives
Moderator: The Motley Crew
Forum rules
There are a few things you should know before posting in these forums. If you are a new user, please click here and read carefully. Thanks a lot!
There are a few things you should know before posting in these forums. If you are a new user, please click here and read carefully. Thanks a lot!
2 Swedish Air Force survival knives
Recently acquired these two fixed blades made by Swedish manufacturer Pontus Holmberg.
According to this website the model was once used as a survival knife for the Swedish Air Force: http://www.gotavapen.se/gota/artiklar/k ... rvival.htm
I'm in the process of giving each one a bit of TLC, and will post some pics later on.
According to this website the model was once used as a survival knife for the Swedish Air Force: http://www.gotavapen.se/gota/artiklar/k ... rvival.htm
I'm in the process of giving each one a bit of TLC, and will post some pics later on.
Re: 2 Swedish Air Force survival knives
Blade hand reground to it's original full convex blade shape on a Foss 7205 black/green silicon carbide stone used with oil, then refined on 400 grit and 1000 grit SiC wet & dry paper used with oil on glass, and the tiny burr stropped off on hard cardboard with 1.0 micron diamond paste.
The new apex measures between 20 and 22,5 degrees inclusive.
Very hard (guesstimate 64-65 HRC) and also very wear resistant steel.
Handle reassembled, now with all washers glued and pommel repolished, then treated to a few coats of warm Granger's wax.
Sheath waxed and hand restitched.
The new apex measures between 20 and 22,5 degrees inclusive.
Very hard (guesstimate 64-65 HRC) and also very wear resistant steel.
Handle reassembled, now with all washers glued and pommel repolished, then treated to a few coats of warm Granger's wax.
Sheath waxed and hand restitched.
- whippersnapper
- Posts: 8426
- Joined: Sat Oct 16, 2004 12:39 pm
- Location: Michigan
Re: 2 Swedish Air Force survival knives
Both Pontus Holmberg knives are made from iron ore from the Dannemora mine, which resulted in very pure steel due to it being rich in manganese.
In earlier centuries it was known as "oregrounds iron": https://en.wikipedia.org/wiki/Oregrounds_iron
However i don't know if that name was still being used by the time these knives were made in the late '40's or early '50's of the 20th century.
Sheffield also used a lot of this same ore to make their famous crucible cast steel from ~1740 up until ~1960.
These two Swedish knives however are noticeably harder as well as much more wear resistant when compared to the vintage English crucible steel knives that i've hand reground/sharpened over the years.
In earlier centuries it was known as "oregrounds iron": https://en.wikipedia.org/wiki/Oregrounds_iron
However i don't know if that name was still being used by the time these knives were made in the late '40's or early '50's of the 20th century.
Sheffield also used a lot of this same ore to make their famous crucible cast steel from ~1740 up until ~1960.
These two Swedish knives however are noticeably harder as well as much more wear resistant when compared to the vintage English crucible steel knives that i've hand reground/sharpened over the years.
Re: 2 Swedish Air Force survival knives
nice rescue. . Thanks for the shop photos. .
I can live vicariously through your images. . .
I can live vicariously through your images. . .
Re: 2 Swedish Air Force survival knives
Currently experimenting a bit with different grits of diamond paste on thin cardboard to see what gives both a nice blade finish as well as a good apex.
Already found that only removing the burr is not enough to get the sharpest of edges on this steel, i have to continue stropping a bit to also get the (presumed tungsten) carbides into the right shape.
I also have to tinker some more with the appearance of the blade finish (now it's a bit too shiny for my taste), but the current apex is reverse hairwhittling sharp (chest hair) @ ~20 degrees inclusive.
Already found that only removing the burr is not enough to get the sharpest of edges on this steel, i have to continue stropping a bit to also get the (presumed tungsten) carbides into the right shape.
I also have to tinker some more with the appearance of the blade finish (now it's a bit too shiny for my taste), but the current apex is reverse hairwhittling sharp (chest hair) @ ~20 degrees inclusive.
Re: 2 Swedish Air Force survival knives
While busy with finetuning the handle the knife slipped out of my rubber coated vise and fell from a measured hight of 1.10 meter on one of the concrete sidewalk tiles which form the floor on my balcony, and landed on the belly part of the edge.
I did not try to catch the falling knife
To my surprise there was only slight denting in that area, no large chips, which i would have expected given the presumed high hardness in combination with the narrow edge angle.
Anyway, due to this i had to regrind the blade again on the green silicon carbide side of my Foss 7205 stone, and that is where i am now.
I did not try to catch the falling knife
To my surprise there was only slight denting in that area, no large chips, which i would have expected given the presumed high hardness in combination with the narrow edge angle.
Anyway, due to this i had to regrind the blade again on the green silicon carbide side of my Foss 7205 stone, and that is where i am now.
Re: 2 Swedish Air Force survival knives
Last edited by kwackster on Wed May 17, 2023 12:04 pm, edited 1 time in total.